C Purlin
Padmashri Steel purlins girts & eve struts are secondary structural members used to support the wall and roof panels. Alfaa purlins are used on the roof, girts are used on the walls and eve struts at the intersection of side walls and roofs.
Padmashri Steel purlins, girts and eave struts are designed in accordance of the American Iron and Steel Institue (AISI) then cold formed design manual.
Padmashri Steel sections may be used over single spans unlapped continuous and lapped continuous span in multi bay buildings.
Padmashri Steel Z&C purlins are available in two Standard Finishes i.e., Red Oxide, Galvanized
Material Specification
Steel Grade
- IS 513/IS 277/IS 10748/IS 1079
- G240 MPA/G340 MPA/G550 MPA, Z 120 GSM/Z 275 GSM & Z 180 GSM
- G indicates Yield Strength in MPA & Z indicates Coating Mass in G/M2
- ALFAA Zed & CEE Purlins with punching
Thickness
- Sleeves
- Cleats
- Sag rods
HR Purlins
- Yield Strength - 240 MPA
- Option - Redoxide Primer Coating
GI Purlins
-
Coating Mass - 120 GSM / 180 GSM / 275 GSM
- Yield Strength - 240 MPA / 340 MPA / 550 MPA
Advantages
Economy
- Savings in steel consumption upto 50% and savings in cost upto 30%
- Savings of transportation & handling, erection and fabrication costs
- No wastages, No surplus left-overs, since sections are supplied in exact required lengths
Design
- High strength, section versatility & wide range of choice
- Having their shear centre within the section, less liable to twist
Structure
- Sleeve system to exploit continuity concept for larger spans
- Empirical design rules apply, hence no design problems
- Excellent surface finish
- Less weight per unit length compared to conventional section without sacrificing the required structural efficiency
- Conforming to the requirements of IS-801, IS-811
Practical Advantages
- Ability to rotate 180 degrees and fit together
- A full range of fixing accessories is supplied. Therefore no extra material needs be procured
- Sections supplied are pre-painted hence prevents corrosion and promotes long life
- Sections are pre-engineered, pre-punched and with complete accessories. No further fabrication required . Considerable savings in erection costs and time.
Typical Connection
Handling and Storage
- Purlin requires appropriate care during storage on site
- The period between delivery and installation to be minimized
- Purlin should be neatly stacked on a ground on a slight slope so that water can drain out
- On open site condition purlins should be protected with water proof covers and condensation
- In case if the bundle of purlins becomes wet , seprate the purlins and wipe & dry it
Technical Specification
| TECHNICAL SPECIFICATION OF Z AND C | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| purlin DEPTH D | Thickness(t) | Mass(Kg/M) | ZED PURLIN | CEE PUTLIN | |||||
| F | L | F | L | ||||||
| 160 | 2.00 | 4.82 | 60 | 20 | 60 | 20 | |||
| 160 | 2.30 | 5.54 | 60 | 20 | 60 | 20 | |||
| 160 | 2.55 | 6.15 | 60 | 20 | 60 | 20 | |||
| 200 | 2.00 | 5.44 | 60 | 20 | 60 | 20 | |||
| 200 | 2.55 | 6.95 | 60 | 20 | 60 | 20 | |||
| 230 | 2.00 | 5.92 | 60 | 20 | 60 | 20 | |||
| 230 | 2.30 | 6.87 | 60 | 20 | 60 | 20 | |||
| 230 | 2.55 | 7.55 | 60 | 20 | 60 | 20 | |||
| 250 | 2.00 | 6.23 | 60 | 20 | 60 | 20 | |||
| 250 | 2.30 | 7.17 | 60 | 20 | 60 | 20 | |||
| 250 | 2.55 | 7.95 | 60 | 20 | 60 | 20 | |||